• FAB Racing Tweets

  • Scottish Championship Tweets

  • MiniGPUK Tweets

  • Gearing "The definitive guide"

    Quite a few threads have popped up recently with people asking about gearing and what works best at certain tracks.
    I thought it may be a good idea to have a definitive gearing thread so everyone can see what's what

    PLEASE NOTE - the Polini Reverse engines I will cover towards the end as they are different calculation.

    Firstly its important that you know how the sprockets work, the front sprocket (Pinion) is a lot smaller, normally around a 6 or 7 teeth, larger sizes are available but rarely used.
    The rear sprockets have a larger range from around 50 to 80 teeth, these let you adjust in small increments whilst changing the front pinion has a bigger effect.

    Final Drive Ratio

    You can calculate the final drive ratio simply by dividing the rear sprocket teeth amount by the front i.e.
    72 divided 6 = 12
    The higher the final drive ratio the faster the acceleration of the bike, obviously the lower the ratio the less acceleration but the bike will have a higher top speed.

    A very useful calculator can be found here http://www.minimotogarage.com/ecm_speed_calc.html

    This will show you final drive ratio, top speed etc etc, be sure to input the correct tyre sizes and max revs for your bike.

    The trick is to balance top speed Vs acceleration to fit the track that you are racing at.

    Polini Reverse Engines

    These work in a different way to the normal engines.
    I have zero experience with them but here is a calculation that I stole from another thread on the forum:
    Rear sprocket teeth No. divided by front teeth No. x 2.157 i.e
    56 divided by 10 x 2.157 = 12.079 Near as dammit 12

    Normal engine track gearing guide

    - - - - - - - - Aircooled--Proddy--Super--Proddy Drive Ration
    o Stretton ---7 x 66 -- 7 x 64 -- 7 x 62------9.14
    o Whilton ---7 x 66 -- 7 x 64 -- 7 x 62-------9.14
    o Swaffam --7 x 72 -- 7 x 70 -- 7 x 68-------9.71
    o Red Lodge 7 x 66 -- 7 x 64 -- 7 x 62-------9.14
    o Wroughton 6 x 68 -- 6 x 66 -- 6 x 64------11
    o Ipswich --- 6 x 73 -- N/A - - - N/A-
    o Witham --- 6 x 73 -- 6 x 72 -- 6 x 70-------12
    o Hully - -- - 6 x 73 -- 6 x 72 - - 6 x 70------12
    o Llandow - - 7 x 67 --7 x 65 -- 7 x 63-------9.28
    o Angmering -6 x 66 -- 6 x 64 -- 6 x 62-------9.14
    o Yarmouth - 6 x 72 -- 6 x 72 -- 6 x 72-------12
    o Kinsham ---7 x 70 -- 7 x 68 -- 7 x 66-------9.71
    o Cheddar -- 6 x 70 -- 6 x 68 -- 6 x 66-------11.33
    o Rowrah ---- 7 x 68 --7 x 66 -- 7 x 64-------9.42

    Obviously the above is a guide only and some people will fare on the smaller or larger side either way, but I thought it would be a good starting point for someone who hasnít been to one of the tracks yet and is looking to go and not be a million miles off the pace.

    If im being honest I've guessed most of the super gearing so chip in if need be, ive also added the Proddy ratio so you can make the reverse engine calculation should you need to.
    This article was originally published in forum thread: Gearing "The definitive guide" started by alboy View original post
    Comments 5 Comments
    1. alboy's Avatar
      alboy -
      It seems some of the above guides are slightly out, a few people mentioned to me that Swaffam should be 7 x 70 on the air cooled bikes
    1. No1papermaker's Avatar
      No1papermaker -
      Hi there pretty new to this, wanting to get a bit more top speed out my mini moto do I need to increase the amount of teeth on the front sprocket? Thanks
    1. alboy's Avatar
      alboy -
      Check the front sprocket size 7 will give you more top end, if its already a 7 the a lower rear sprocket size (less teeth)
    1. maddog's Avatar
      maddog -
      Just rode swafham on my super and the gearing was 7-64 ........ Anyone know what's the best super gearing for red lodge
    1. themadturnip's Avatar
      themadturnip -
      Good advice on gearing, explains it all thank you.
  • Recent Forum Posts


    Tell me more

    So still haven't got the bike up and running yet been reading as much info as possible on here to make sure I get it set up sweet. So far I've done the

    ianh8026 4 Days Ago Go to last post

    Identification pls

    McIntosh would be your man for pads as heís the DM dealer and they used the niffo brakes

    Bullit 5 Days Ago Go to last post

    Tell me more

    Yes thatís all standard Pasini bits there mate

    Nice bikes to ride

    Bullit 5 Days Ago Go to last post